banner



Home  ›  How To Repair Trim Around Door

How To Repair Trim Around Door

Written By Sunday, 19 June 2022 Add Comment Edit

Download Article

Download Commodity

Door trim, peculiarly forest trim exposed to the weather, can rot and become damaged over time. Information technology'southward not besides difficult to supplant, simply you exercise demand to exist able to use a miter saw. The old trim is easy to pull off with a pry bar. So, cutting the new trim to size and blast it in place. When you're finished, stain or paint the trim to match it with the residual of your house.[ane]

  1. 1

    Cut through the caulking with a utility knife. Work your pocketknife's bract under the exterior border of the trim. You may also cut through some paint while doing this, but that's okay. Cut all the way effectually the trim to free it.[two]

    • Brand certain to cut all the manner through the caulking to avoid damaging the paint when y'all pry off the trim.

  2. 2

    Utilize a pry bar to pull off the trim. Slide the border of the pry bar under the trim nigh a nail. You tin can tap a hammer against the back of the bar to help wedge it in. Pull back i slice of trim at a fourth dimension, taking care not to damage the walls and door jamb. It doesn't matter which side yous start on, as long as yous remove all the pieces you want to supercede.[iii]

    • To protect the walls, hold a scrap of wood against the wall and rest the dorsum of the pry bar confronting information technology equally y'all work. There'due south not actually a way to protect the jamb besides being very careful when leveraging the trim.

    Advertisement

  3. 3

    Scrape off any remaining caulking with a knife. Employ the utility knife or a chisel to remove any quondam caulk left over. You may also need to scrape down thick layers of paint to level out the space where the new trim will balance.[iv]

    4. Advertisement

  1. one

    Measure the new trim confronting the door. Start, purchase some trim from the home comeback store. Most trim comes in eight or 10 ft (2.4 or 3.0 m) sections. Utilize your erstwhile trim as a sizing guide or hold the new trim against the door frame.[5] Marking the measurements with a pencil and so you lot know how to size the trim.[six]

    • You tin can always measure out the space around the door with a tape measure if the other options aren't possible. Measure out out the length and width of the trim infinite on all sides of the door to observe out how much trim you need.
    • Narrower trim tin exist a skilful choice for simplicity and appearance, just make sure yous go out enough material to comprehend the gap between the door frame and wall.
    • Wider trim stands out more, merely it'll cover more than of the wall. Make sure you accept enough infinite for it.

  2. ii

    Put on ear and eye protection earlier sawing. Encompass your eyes with a pair of polycarbonate safety glasses. Miter saws are loud, and then besides put on a pair of earmuffs or cream earplugs. Avert putting on gloves or whatsoever other loose clothing that could get defenseless in the saw.[7]

  3. 3

    Cut the trim pieces with a miter saw. Set the miter saw to cut at an bending of exactly 45°. Line upwards the trim and cut from the inside edge diagonally upwards to the outside edge. Cut a big piece of trim into the top piece and i of the sides.[8]

    • It's okay to leave the trim a picayune long at first. Yous can adapt this equally needed later.
    • It'south helpful to practise using the miter saw on fleck forest first. You lot are normally able to arrange the saw more than than you lot expect to get a better-plumbing equipment joint.

  4. 4

    Cut the side trim to length. Line up the side pieces of trim confronting the door. If the trim is long, measure up from the bottom to mark how much length needs to exist removed. Cut the bottoms of the side trim pieces evenly then they match and fit on the door frame.[9]

  5. 5

    Cutting the top trim to the advisable size. Concord the header confronting the 2 side pieces. This piece has miter joints on both sides, which should fit snugly against the residue of the trim. If you lot accept to reduce the header, make sure the miter is prepare at a 45° angle. Redo the cut until the header fits in place.

    6. Advertisement

  1. 1

    Position the trim against the wall. Place the pieces without attaching them to double-check the fit. Pay attention to how the header piece fits on top of the side pieces. Make any adjustments needed by further cut down the size of the trim.[10]

  2. 2

    Nail the side trim in place. Use a finish nailer to secure the trim. On the inside part, which covers the door jamb, use 4d or 1.5 in (iii.8 cm) finishing nails. On the exterior part, which attaches to the wall, employ 6d or two in (v.1 cm) finishing nails to secure the trim.[11]

    • Avert placing the nails close to the ends of the trim.
    • Depending on the thickness of your trim, yous may need larger nails. Hold the nails up to the trim to run into if they're long enough to go all the fashion through to the wall.

  3. 3

    Drill and nail the header in place. Stand up on a stepstool to attain the peak office of the door. Place the elevation trim, checking one final time to brand certain it'due south the right size. When finished, adhere it the same way y'all did the other pieces.[12]

  4. 4

    Pre-drill holes in the trim'south corners. Push the trim pieces together to tighten them a piffling more. Measure out about 1 in (2.5 cm) from the sides of the header. Drill a 1⁄xvi  in (one.6 mm) hole downwards through the superlative of the header. Measure down the side pieces and drill a hole through each from the outside edge.[thirteen]

    • Concord a piece of cardboard against the wall to foreclose your tools from damaging information technology.

  5. 5

    Nail the trim pieces in place. Stick 3d or 1.25 in (iii.ii cm) nails in each hole. Starting time on i side of the door. Alternate hit the top and side nails so that the trim doesn't autumn out of alignment. When finished, move on to the other side.[14]

  6. 6

    Caulk the holes, joints, and edges of the trim. The holes and miter joints can be filled with painter'due south putty, woods filler, or a paintable acrylic or silicone caulk as needed. Spread it using a putty pocketknife or your fingers. And then go effectually the outside of the trim, squeezing a small bead of caulk betwixt the trim and the wall. Run your finger along the bead of caulk to smooth information technology out, so wipe it clean on a wet rag.[xv]

    • You lot'll need to permit the caulk dry before painting or staining. Cheque the label information to find out how long this takes.

  7. seven

    Sand, prime number, and paint the door frame. [16] Sand the door frame lightly to make information technology smoothen and fifty-fifty. You can further customize your trim by staining or painting it. The trim tin can be colored with primer and a layer of paint. Y'all can also retain the appearance of wood trim past using a commercial staining product to color information technology.[17]

    • Employ an oil or latex-based primer before painting over woods.

    8. Advertisement

Ask a Question

200 characters left

Include your email address to become a bulletin when this question is answered.

Submit

Advertisement

  • Measure more than one time before cutting trim to reduce the chances of making an mistake.

  • Narrower trim tin stand out less and fit in tight spaces, but if y'all cut it too narrow, it'll go out unsightly gaps around the door.

  • Wider trim stands out more and ensures that door frame gaps are covered. Make certain you lot can fit the trim effectually the door and are okay with covering more wall infinite than usual.

Advertisement

Things You'll Demand

  • Tape measure
  • Miter saw
  • Condom glasses
  • Hearing protection
  • Drill
  • Hammer
  • Pry bar
  • Utility knife
  • Nails
  • Caulk
  • Forest putty for wood trim
  • Trim

Nearly This Article

Article Summary 10

Replacing a door trim involves removing the sometime ane, cutting your new trim to the correct size, and nailing it to the doorjamb. Start by cutting the caulk from your door trim with a utility pocketknife. Then, utilize a pry bar to remove each side of the trim. Slide the bar in near each nail to help you lever it away from the jamb. Once you've removed the trim and any leftover caulk, measure your door jamb to help you cut the new trim. You'll need a miter saw to cut the corners at 45 degree angles so the pieces fit together. When you've cutting all of the trim pieces, use 1.5-inch finishing nails to secure the inside part of the trim to the jamb. On the outside office, which attaches to the wall, utilise 2-inch finishing nails. After y'all've finished nailing the trim in identify, utilize caulk over the nail holes and around the edge to brand the trim await flush. For more tips, including how to paint and stain your new door trim, read on!

Did this summary help you?

Thanks to all authors for creating a page that has been read 94,797 times.

Did this article assistance y'all?

Source: https://www.wikihow.com/Replace-a-Door-Trim

0 Response to "How To Repair Trim Around Door"

Post a Comment

Subscribe to: Post Comments (Atom)

Iklan Atas Artikel

Iklan Tengah Artikel 1

Iklan Tengah Artikel 2

Iklan Bawah Artikel